Quattro 48/5000/70-100/100 VE.Bus
5000VA pure sine inverter 48V + internal 70A IUoU battery charger + 2x AC transfer switch each 100A
designed for Caravan, Boat, Motor home and Offgrid systems
Similar to the MultiPlus, the Quattro is also a combined inverter and charger. Additionally it can accept two AC inputs and automatically connect to the active source. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology plus multiple system integration features such as three or split phase operation and parallel operation.
Features:
PowerControl
Dealing with limited generator, shore side or grid power. The Quattro is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (nearly 10 A per 5 kVA Quattro at 230 VAC). With the Multi Control Panel a maximum generator or shore current can be set. The Quattro will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.
PowerAssist
Boosting the capacity of shore or generator power. This feature takes the principle of PowerControl to a further dimension. It allows the Quattro to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the Quattro will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.
Remote control: Digital Multi Controll (optionally available)
The Digital Multi Control is used to remotely view and adjust AC input currents, and turn on and off the Multi or Quattro. It is designed to integrate cleanly with your boat, vehicle or house system control panel.
Adaptive 4-stage charging characteristics: bulk – absorption – float – storage
The microprocessor-driven adaptive battery management system can be adjusted for various types of batteries. The adaptive function automatically adapts the charging process to battery use.
Uninterrupted AC power
In the event of a grid failure, or shore or generator power being disconnected, the inverter within the Quattro is automatically activated and takes over supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.
Programmable relay
The Quattro is equipped with 3 programmable relays that by default is set as an alarm relay. The relays can be programmed for all kinds of other applications however, for example as a starter relay for a generator.
Virtually unlimited power thanks to parallel operation
Up to 6 Multis can operate in parallel to achieve higher power output. Six 12/5000/220 units, for example, will provide 25 kW / 30 kVA output power with 720 Amps charging capacity.
Threephase capability
In addition to parallel connection, three units of the same model can be configured for three phase output. But that’s not all: up to 6 sets of three units can be parallel connected for a 75 kW / 90 kVA inverter and more than 2000 Amps charging capacity.
Solar energy:
AC power available even during a grid failure. The Quattro can be used in off grid as well as grid connected PV and other alternative energy systems. Loss of mains detection software is available.
System configuring
-In case of a stand-alone application, if settings have to be changed, this can be done in a matter of minutes with a DIP switch setting procedure.
-Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software.
-Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT Solar Chargers can be configured with Assistants (dedicated software for specific applications).
On-site Monitoring and control
Several options are available: Battery Monitor, Multi Control Panel, Color Control GX or other GX devices, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).
Remote Monitoring and control
Color Control GX or other GX devices.Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.
Remote configuring
When connected to the Ethernet, systems with a Color Control GX or other GX device can be accessed and settings can be changed remotely.
The interface cable for configuration via PC or laptop can be found here: MK3-USB
The remote controls, in two optically different versions, can be found here: Digital MultiControl oder Digital MultiControl GX
To view the technical data, click on the tab 'Technical data' above.
Delivery contains:
- Victron Quattro / 48V / output power 5000VA / 70A battery charger / 2 x 100A AC transfer switch, Victron QUA485021010
Battery cables must be ordered separately! - Battery temperature sensor
- Of course, you will also receive from us an instruction manual in German and English
Further helpful tips can be found on our FAQ Questions / Answers page under the following link: FAQ
